Supports the following connector types:
- Traxxas
- Tamiya
- Mini Tamiya
- JST
- Hitec
- EC3
- Deans
Supports multiple types of battery packs with one single charger! The follow packs are supported:
- NiMH/NiCD 1~15 cells ( 1.2v to 18v)
- Li-PO/Lithium Ion 1~6 series ( 3.7v to 22.2v)
- Li-Fe 1~6 series
- Sealed Lead Acid (SLA)
Charger Specifications:
- Handle NiMH, NICD, Li-Po,Li-ion, Li-Fe, SLA Batteries
- Build-in Balancer
- DC 11V~15V, which can be directly connect to Automobile Battery. The working electric current is less than 5A when it is charged in full load. The current of the fuse is 10A which could prevent short circuit.
Optimized operating software
When charging or discharging, TB6 has an 'AUTO' function that sets the feeding current or the cell count of the battery automatically. Especially for Li-ion/Li-Polymer batteries, it can prevent the over-charging can lead to an explosion by users fault. Every program in the unit is controlled with mutual links and communication for every possible error so it introduces a maximum safety. These can be set at users option.
Individual voltage balancer for Li-ion/Li-Polymer batteries inside
TB6 has an individual-cell-voltage balancer inside. So it does not need any balancer separately when charging Li-ion/Li-Polymer batteries (LiIo/LiPo/LiFe) for cell voltage balancing.
Balance individual cells on discharge
TB6 also can monitor and balance individual cells of the battery pack during the discharge process. If the voltage of any one cell varies abnormally, the process will be stopped with the error message.
Accept various types of battery
TB6 can accept three types of batteries - LiIo, LiPo and LiFe. They have different characteristics by their chemistry. You can select any one of them that you are going to process before the job.
Battery 'Fast' and 'Storage' mode
You can charge Li-ion/Li-Polymer battery for special purposes. 'Fast' charge reduces the charging time of battery and 'Storage mode controls the final voltage of the battery to be suit for long time storage.
Data store/load
For users convenience it can store maximum 5 data of different batteries. You can establish the data contains program setting of the battery to charge or discharge continually. These data can be called out at any time you need and the process can be executed without program setting.
Cyclic charging/discharging
Perform 1 to 5 cycles of charge>discharge or discharge>charge continually for battery refreshing and balancing.
Robust outer aluminum case
High-quality aluminum case is durable and very efficient to cool out the internal heat
Specification
- Operating voltage:
DC 11~18 volts
AC 100~240V, 50/60Hz
- Charge/discharge power:
max. 50/5 Watts
- NiCd/MH:
1~15 cells
- LiIo/LiPo/LiFe:
1~6 series
- Pb:
2~20V
- Charge current:
0.1 to 5.0A
- Discharge current:
0.1 to 1.0A
- No. of cycle:
1 to 5 times
- Battery data memory:
up to 5 data
User's setting-up parameters
- Battery voltage type:
LiIo:3.6V, LiPo:3.7V, LiFe:3.3V
- NiCd Delta-peak voltage sensitivity:
1 to 20mV
- NiMH Delta-peak voltage sensitivity:
1 to 20mV
- Battery temperature cut-off:
20 to 80C or OFF
- Waiting time between charge/discharge:
1 to 60 min.
- Integral timer limit for safety:
10 to 720 min.or OFF
- Maximum charging capacity limit for safety:
10 to 9990mAh or OFF
- Key beep and buzzer sound:
ON/OFF
- Input DC power low alert:
10 to 11V
